low beam TOYOTA LAND CRUISER 2020 Owners Manual (in English)

5
Low fuel level warning
Parking brake indicatorShift position and range indicators
Low Tire Pressure Warning1
Malfunction/Check Engine indicator1
Master warning1,2
Second start indicator (Automatic
Transmission)
Power mode indicator
Slip indicator1,3
Low speed four-wheel drive indicatorMulti-terrain select indicator
ECO driving indicator1
Turn assist function indicator
TRAC OFF indicator1
Turn signal indicator
Fog light indicator
Open door warning Pre-Collision System (PCS)
warning
1,2
Lane Departure Alert (LDA) indicator
Headlight low/high beam
indicator
Vehicle Stability Control (VSC) OFF
indicator1
OVERVIEW
FEATURES & OPERATIONS
TOYOTA SAFETY SENSE
SAFETY & EMERGENCY FEATURESDynamic Radar Cruise Control
(DRCC) indicator/DRCC SET
indicator
Driver seat belt reminder
(alarm will sound when the engine switch
is IGNITION ON mode)
Front passenger seat belt reminder
(alarm will sound if the seat belt is not
fastened)
1
If the indicator does not turn off within a few seconds of starting the \
engine, there may be a
malfunction. Have the vehicle inspected by your Toyota dealer.
2 If the indicator flashes, there may be a malfunction. Refer to the Owner\
’s Manual.3 If the indicator flashes, it indicates that the system is operating.4 If equipped.

17
OVERVIEW
FEATURES & OPERATIONS
TOYOTA SAFETY SENSE
SAFETY & EMERGENCY FEATURES
Daytime Running Light system (DRL) Automatically turns on under certain
conditions to make vehicle more visible to other drivers. Not for use at\
night. Automatic light cut off system Automatically turns lights off after 30 second
delay. Automatic High Beam (AHB) system Automatically switches between high
and low beams as appropriate to enhance vision at night.

Refer to Toyota Safety Sense™ P (TSS-P) in this guide or the Owner’\
s Manual for
more details on the Automatic High Beam feature.
* Operating conditions must be met. Refer to the Owner’s Manual for d\
etails.
Right turn
Lane change
Lane change Left turn
AutoOFF
Parking lights
Headlights
TurnOFF
ON
Front fog lights come on only when the headlights are on low beam.
Low beamHigh beam flasher
or
Automatic High Beam*
High beam
Lights & turn signals
HEADLIGHTS
FRONT FOG LIGHTS
TURN SIGNALS

34
Refer to the Owner’s Manual for operation, setting adjustments, limitations and
more details to understand these functions and complete safety precautions. For
more information, please go to http://www.toyota.com/safety-sense
Pre-Collision System with Pedestrian Detection (PCS w/PD)
PCS w/PD is designed to provide alert, mitigation, and/or avoidance
support in certain conditions, when the system detects a potential
collision with a preceding vehicle is likely to occur.
The advanced millimeter-wave radar sensor system is designed to
work with the camera sensor to help recognize a preceding pedestrian,
and provide an alert, mitigation and/or avoidance support in certain
conditions.
Lane Departure Alert (LDA)
LDA is designed to provide notification when the system detects an
unintended lane departure.Automatic High Beams (AHB)
AHB is designed to detect the headlights of oncoming vehicles and the
tail lights of preceding vehicles and switch between high beams and
low beams as appropriate.
Dynamic Radar Cruise Control (DRCC)
DRCC is designed to help maintain a pre-set distance to a preceding
vehicle when the preceding vehicle is traveling at a lower speed.
Quick overview-Toyota Safety Sense™ P (TSS-P)
Sensors
Toyota Safety Sensee™ 1 5441
is a set of active safety technoMogies designed to
help prevent or mitigate collisions across a wide range of traffic situa\
tions. TSS-P
is designed to help support the driver’s awareness, decision making a\
nd vehicle
operation contributing to a safe and comfortable driving experience.
TSS-P Combines an in-vehicle camera mounted in front of the inside rear \
view
mirror and a millimeter-wave radar mounted in the front grille. These se\
nsors
support the driver assist systems.
Radar sensor Camera sensor
TOYOTA SAFETY SENSE

44
Automatic High Beams (AHB)
TOYOTA SAFETY SENSE
ACTIVATING THE AHB SYSTEM
CONDITIONS WHERE AHB WILL TURN ON/OFF AUTOMATICALLY
When all of these conditions are met, high beams will be automatically t\
urned on
after aQQroYimateMy  second
t 7ehicMe sQeed is aCove aQQroYimateMy  mQh  Lmh.

• The area ahead of the vehicle is dark.
• There are no oncoming or preceding vehicles with headlights or tail\
lights turned on.
• There are few streetlights on the road ahead.
If any of these conditions occur, the system is designed to automaticall\
y turn off
high beams: t 7ehicMe sQeed droQs CeMow aQQroYimateMy  mQh  Lmh
.
• The area ahead of the vehicle is not dark.
• Oncoming or preceding vehicles have headlights or tail lights turne\
d on.
• There are many streetlights on the road ahead.

8ith the engine switch in I(/I5I0/ 0/ mode and headMight switch turned to “AUTO” or “
” position, push lever away from you.

1ress the Automatic )igh #eam i
” switch.
The AHB indicator will come on when the headlights are turned on automat\
ically
to indicate that the system is active.
Note: Pull the lever back toward you to turn the AHB system off.
The AHB indicator will turn off and the high beam indicator turns on. AHB is a safety system designed to help drivers see more of what’s ah\
ead at
nighttime while reducing glare for oncoming drivers. When enabled, AHB u\
ses an
in-vehicle camera to help detect the headlights of oncoming vehicles and\
tail lights
of preceding vehicles, then automatically switches between high and low \
beams
as appropriate to provide the most light possible and enhance forward vi\
sibility.
By using high beams more frequently, the system may allow earlier detect\
ion of
pedestrians and obstacles.
Refer to the Toyota Owner’s Manual for additional information on AHB \
operation,
settings adjustments, limitations, and precautions before attempting to \
use it. (1)
(2)